Hotline:0755-22277778
Tel:0755-22277778
Mobile:13826586185(Mr.Duan)
Fax:0755-22277776
E-mail:duanlian@xianjinyuan.cn
Single component thermoplastic conductive adhesiveThe main components are thermoplastic adhesive andSilver powderAnd solvents. This product has low viscosity, smooth dispensing, and does not flow after dispensing. It has shape retention (after dispensing, the adhesive points do not collapse, deform, or diffuse) and good conductivity after baking. It has excellent adhesion to materials such as metal, glass, and ceramics. Mainly used for LCM bonding.
Research platinum expertise
Good conductivity and stable resistance
U has good adhesion to various materials
Smooth dispensing without drawing or trailing
U has strong flexibility and good impact resistance
Research on Platinum Applications
Conductive bonding of electronic components
Properties before curing
Items | Data |
Remark |
project | Measurement value | Preparing for exams |
Appearance appearance |
Silver silvery white |
|
Viscosity viscosity |
6000±500mPas | Brookfield,52Z, 5rpm |
Specific gravity proportion |
2±0.5g/ml GB/T 13354-1992 |
Cup Proportion Cup |
Cure time Curing time |
5-60min | 25℃*60min 80℃*5min |
Items | Data | Remark |
project | Measurement value | Preparing for exams |
Pencil hardness Pencil hardness |
HB-3H | GB/T6739-2006 |
Lap shear strength shear strength |
3MPa | Glass/nickel plated copper sheet 10mm/min |
Peel strength peel strength |
19N/25mm | Glass/nickel plated copper sheet 10mm/min |
Volume resistivity Volume resistance |
<0.0005Ω.cm | GB/T 15662-1995 |
Preparation method of test piece: Prepare a test strip with a width of 1cm, a thickness of 25um, and a length of 5cm. After curing at 25 ℃ for 60 minutes, test the volume resistance.
Direction for use usage guide
Please wipe off the moisture, oil, rust and other dirt on the surface of the parts that need to be bonded, and then apply glue. Surface dirt will greatly reduce the bonding strength.
Use an automatic glue dispenser to apply glue.
Storage conditions
This product belongs to resin andSilver powder mixed adhesiveSilver powder has a high density and is prone to sinking, resulting in uneven performance. Therefore, low-temperature storage is beneficial for extending the shelf life. It is recommended to store it frozen, with the optimal storage temperature being -10 ℃ to 5 ℃ and a shelf life of 6 months. Before opening, the lid must be allowed to warm up at room temperature for 2-4 hours. After opening, keep the opening clean and sealed, and use it as soon as possible.
Caution precautions
Please keep it out of reach of children.
When using, it is necessary to wear protective equipment such as masks, gloves, eye masks, etc., and use them in places with good ventilation or exhaust systems.
If you accidentally come into contact with your eyes or skin, please rinse with water and seek medical treatment.
Stop using this product immediately and seek medical treatment if you are allergic or have abnormal sensations.
Please do not use it for medical devices or for purposes that come into contact with the human body.
Note Declaration
The technical data recorded in this article are measured values obtained based on the corresponding Chinese national standards and our company's experimental conditions and methods. We cannot guarantee that other companies will obtain the same results from testing.
Before using this product, users should fully verify its scope of application and purpose, carefully read the SDS of this product, confirm the chemical hazards contained in this product, and take corresponding safety protection measures. We do not assume responsibility for safety and health accidents caused by misuse or misoperation.
Packaging specifications
U200g/bottle; 10CC/branch; 5CC/branch
Advanced Institute (Shenzhen) Technology Co., Ltd, © two thousand and twenty-onewww.leird.cn. All rights reservedGuangdong ICP No. 2021051947-1 © two thousand and twenty-onewww.xianjinyuan.cn. All rights reservedGuangdong ICP No. 2021051947-2